Centurion FAAC 844 Specifications Page 1

844Slide Gate OperatorFAAC International Inc.Headquarter & East Coast Operations5151 Sunbeam RoadSuites 9-11Jacksonville, FL 32257Tel. 866 925 322

10FAAC MODEL 844 Slide Gate Operator15 ¾ - Measurements in Inches2 ½24 ⅜ (Z16)4 ¾ (Z20)⅝ to 1 ¼ - Measurements in Inches1. Manually move the leaf to

11FAAC MODEL 844 Slide Gate OperatorNotes on Rack InstallationFig. 17116inch• Make sure that, during gate travel, no rack elements derail from the pi

12FAAC MODEL 844 Slide Gate Operator–+DLLedF1J1J2LedJ5FJ7F2J8J6Fig. 221 OPEN A (total opening)2 OPEN B (partial opening)3 FSW-OP (opening safety d

13FAAC MODEL 844 Slide Gate OperatorSAFE++OPEN BOPEN AOPCLJ1J5AAAFig. 235.4.1. Connection of Photocells and Safety DevicesBefore connecting safety de

14FAAC MODEL 844 Slide Gate OperatorSAFE++OPENBAOPENOPCLFig. 30Connection of a pair of closing photocellsSAFE++OPENBAOPENOPCLFig. 29Connection of a pa

15FAAC MODEL 844 Slide Gate Operator5.4.2. J7 Terminal Block - Power Supply (Fig. 23)POWER SUPPLY (Terminals PE-N-L): PE : Ground connection N :

16FAAC MODEL 844 Slide Gate OperatorFRPFig. 38Fig. 39TX -FSW - Negative for Power Supply to Photocell Transmitters (Terminal 11)If you use this termin

17FAAC MODEL 844 Slide Gate OperatorF++FORCE:Adjusts Motor thrust. = minimum force = maximum forceOPENING DIRECTION:Indicates the gate opening movemen

18FAAC MODEL 844 Slide Gate OperatorDisplay Function Default Display Function DefaultOPENING PHOTOCELLS LOG

19FAAC MODEL 844 Slide Gate Operator6. START-UPFig. 4021FC2FC1Fig. 41FC2FC1Fig. 426.2. DEFINITION OF OPENING DIRECTION AND OPERATION OF LIMIT-SWITCH

2FAAC MODEL 844 Slide Gate OperatorIMPORTANT SAFETY INFORMATION 4Important Safety Instructions 4Important Installation Instructions 4General Safety

20FAAC MODEL 844 Slide Gate OperatorA BFig. 46Fig. 45Fig. 44Fig. 437. FINAL OPERATIONS6.7. CHECK OF STOP POINTSBe careful when setting the post-limi

21FAAC MODEL 844 Slide Gate OperatorFig. 49To prevent an involuntary pulse from activating the gate, cut power to the system before re-locking the ope

22FAAC MODEL 844 Slide Gate Operator"PA"cigoL SESLUPSUTATSETA AG -NEP BO -NEP PO OT SS ECIVEDYTEFASGNINEP SO ECIVEDYTEFASGNISOL EC CIVEDYTEF

23FAAC MODEL 844 Slide Gate Operator(1) If maintained, it prolongs the pause until disabled by the command (timer function) (3) During the partial op

24FAAC MODEL 844 Slide Gate Operator13. 844 SPARES DIAGRAMPOS. P/N DESCRIPTION01 7273425 844 OPERATOR PLASTIC COVER02 7111245 746/844 COVER HOLES CAP

25FAAC MODEL 844 Slide Gate OperatorPOS. P/N DESCRIPTION31 702705 NUT WITH LOCKING WASHER M4 32 701000 TCEI 4X 25 5931 12 K33 752207 LUG CEMBRE BF-M53

26FAAC MODEL 844 Slide Gate Operator14. TROUBLESHOOTINGIf you have a problem installing the operator, check the problems and solutions listed below fo

27FAAC MODEL 844 Slide Gate OperatorTo the original purchaser only: FAAC International, Inc., warrants, for twenty-four (24) months from the date of i

3FAAC MODEL 844 Slide Gate OperatorLIMITED WARRANTY 27FAAC Model 844 - Rev: 01 - December 2010 Read this instruction manual before you begin install

4FAAC MODEL 844 Slide Gate Operator1. Install the gate operator only when the following condi-tions have been met:• The operator is appropriate for

5FAAC MODEL 844 Slide Gate OperatorGate ConstructionVehicular gates should be constructed and installed in accordance with ASTM F2200: Standard Speci

6FAAC MODEL 844 Slide Gate OperatorRESIDENTIAL VEHICULAR GATE OPERATOR CLASS IA vehicular gate operator system intended for use in a single family dwe

7FAAC MODEL 844 Slide Gate OperatorMODEL 844 OPERATORThese instructions apply to the following models:844 ER Z16 CR, 844 R, 844 R CAT, 844 R RFThe FAA

8FAAC MODEL 844 Slide Gate OperatorTABLE 1: SPECIFICATIONS FOR 844 OPERATORMODEL844Power Supply (VAC +6% -10% 60Hz)115 or 230Absorbed Power (W)650Redu

9FAAC MODEL 844 Slide Gate Operator28 ¾0 to 2 - Measurements in Inches2.5 - Measurements in InchesFig. 4Fig. 5Fig. 74.1. PRELIMINARY CHECKSTo ensur