Centurion VECTOR2 Installation Manual Page 56
- Page / 82
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Page 52
24. Controller Features
This level should only be used if additional safety measures are taken
(e.g. Infrared Safety Beams, etc.).
Collision Force can be set independently per direction of travel.
Menu 2 - Safety (Collision Force)
1. Collision Force
If the gate is obstructed, the internal collision circuitry will activate.
The response of the system to a collision will vary, depending on the Profile
selected (Operating Standard, e.g. ZA). Responses can vary from the gate
stopping, to the gate reversing. The Collision Force can be set from minimum
to maximum in five discrete steps.
A sixth step will disable collision sensing entirely, allowing maximum force to
be achieved. Under this condition, the motor will continue running until it
stalls, at which point a collision will be detected.
Menu 3 - Autoclose
1. Autoclose status
When turned on, the Autoclose feature has the function of automatically
closing the gate after a preset Autoclose time. The Autoclose feature is
automatically turned on when the controller is set for Condominium Mode.
2. Autoclose time
The Autoclose time can be set anywhere from 1 to 255 seconds.
3. Autoclose Override
It is possible for the user to temporarily turn off Autoclose when the Mode of
Operation is Standard or Reversing. To activate Autoclose Override, the
Trg input must be activated and maintained for a period longer than the time
set for the Autoclose Override Time.
The gate response will be to start opening on the Trg trigger, and then to stop
as soon as the Autoclose Override feature is activated. On clearing of the
Trg input, the gate will continue opening until fully open. The Autoclose
feature is now off and the gate will remain open indefinitely.
The next signal received on Trg will clear the Autoclose Override feature,
close the gate, and set the Autoclose feature back to normal.
4. Autoclose Advanced Options
The conditions under which the gate will automatically close can be set within
the Advanced Autoclose options menu:
2. Collision Count
A counter monitors the number of collisions that the gate experiences before
it reaches the fully closed position. If the value exceeds the value set in the
Multiple Collision Counter the controller shuts down until the next valid
trigger is received. As an indication, the status LED will flash four times every
two seconds. The Multiple Collision fault indication will continue to flash
indefinitely or until a valid trigger has been received.
- SWING GATE 1
- OPERATORS 1
- Company Profile 2
- Contents 3
- Mechanical Setup 5
- Electrical Setup 6
- Commissioning 6
- IMPORTANT 7
- 1. Declaration of Conformity 9
- 2. General Description 10
- 3. Icons Used in this Manual 11
- 4. Specifications 12
- VECTOR2 400 VECTOR2 500 13
- Technical Specifications 13
- Control Card 14
- Power Supply 14
- Allowable Gate Mass 15
- 5. Product Identification 16
- FIGURE 3C. WALL ADAPTOR KIT 17
- FIGURE 3D. HIGH-SECURITY KIT 17
- FIGURE 3E. MECHANO KIT 17
- FIGURE 3F. GATE ADAPTOR KIT 17
- FIGURE 4 18
- 7. Preparation of Site 19
- Strength of the Pillar 20
- FIGURE 8 21
- FIGURE 9 21
- FIGURE 10 21
- FIGURE 11 21
- FIGURE 14 22
- FIGURE 12 22
- FIGURE 13 22
- FIGURE 18 23
- FIGURE 15 23
- FIGURE 16 23
- FIGURE 17 23
- 8. Cabling Requirements 26
- 10. Operator Installation 28
- Determine the Gate Bracket 29
- Position 29
- FIGURE 35 30
- FIGURE 34 30
- FIGURE 36 30
- Fasten Gate Bracket to Gate 31
- Adjust Origin Clamp 32
- Gate closed 33
- Gate open 33
- For V400 (400mm operator) 34
- For V500 (500mm operator) 35
- Outward Swing Gate Setup 36
- FIGURE 53 37
- FIGURE 54 37
- FIGURE 55 38
- FIGURE 56 38
- FIGURE 57 39
- FIGURE 58 39
- 12. Allowable Wind Load 40
- Secure Control Box to Wall 41
- Connect all Wiring 41
- Setting the Limits 42
- FIGURE 65 43
- Master Motor (MTR M) 48
- Slave Motor (MTR S) 49
- Fuse protection 50
- 21. Solar Panel Wiring 51
- FIGURE 74. VIEW OF CONTROLLER 52
- 23. Menu Navigation Map 53
- 24. Controller Features 56
- Menu 4 - Modes of Operation 57
- Menu 5 - Run Profile 57
- FIGURE 78 58
- FIGURE 77 58
- FIGURE 76 58
- FIGURE 75 58
- Menu 6 59
- IR beams 59
- FIGURE 80 60
- FIGURE 81 61
- FIGURE 82 61
- Menu 7 - Pedestrian Opening 62
- Menu 8 - Gate Lock 63
- Menu 10 - General Features 64
- Menu 11 - Remote Controls 65
- 25. Factory Defaults Schedule 67
- CE Standard Profile 69
- UL325 Standard Profile 71
- 27. Diagnostics 76
- LCD Display 77
- Buzzer Feedback 78
- 28. Installation Handover 79
- Head Office: +27 11 699 2400 82
- +27 11 699 2481 82
Related products and manuals for Garden tools Centurion VECTOR2
Garden tools Centurion D3 User's Guide
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 1.472 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals