Centurion VECTOR2 Installation Manual Page 79
- Page / 82
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
28. Installation Handover
Once the installation has been successfully completed and tested, it is important for the
installer to explain the operation and safety requirements of the system.
NEVER ASSUME THE USER KNOWS HOW TO SAFELY OPERATE AN AUTOMATED
GATE!
Even if the user has used one before, it does not mean he knows how to SAFELY operate
it. Make sure that the user fully understands the following safety requirements before
finally handing over the site.
The following needs to be understood by the user:
How to operate the manual release mechanism. (Show them how by demonstration)
How the obstruction detection and all other safety features work. (Show them how
by demonstration)
All the features and benefits of the operator, i.e. Beams, etc.
All the safety considerations associated with operating an automated gate.
The user should be able to pass this knowledge on to all other users of the
automated system and must be made aware of this responsibility.
Do not activate the gate operator unless you can see it and
can determine that its area of travel is clear of people, pets,
or other obstructions
NO ONE MAY CROSS THE PATH OF A MOVING GATE.
Always keep people and objects away from the gate and its
area of travel
NEVER LET CHILDREN OPERATE OR PLAY WITH THE GATE
CONTROLS, and do not allow children or pets near the gate area
Be careful with moving parts and avoid close proximity to areas
where fingers or hands could be pinched
Secure all easily-accessed gate operator controls in order to prevent
unauthorised use of the gate
Keep the automated gate system properly maintained, and ensure
that all working areas are free of debris and other objects that could
affect the gate operation and safety
On a monthly basis, check the obstruction detection system
and safety devices for correct operation
All repair and service work to this product must be done
by a suitably qualified person
This product was designed and built strictly for the use indicated in
this documentation. Any other use, not expressly indicated here,
could compromise the good condition/operation of the product
and/or be a source of danger!
Centurion Systems (Pty) Ltd does not accept any liability caused by improper use of the
product, or for use other than that for which the automated system was designed.
Ensure that the customer is in possession of the User Guide and that you have
completed the installation details in the back of the User Guide.
Page 75
- SWING GATE 1
- OPERATORS 1
- Company Profile 2
- Contents 3
- Mechanical Setup 5
- Electrical Setup 6
- Commissioning 6
- IMPORTANT 7
- 1. Declaration of Conformity 9
- 2. General Description 10
- 3. Icons Used in this Manual 11
- 4. Specifications 12
- VECTOR2 400 VECTOR2 500 13
- Technical Specifications 13
- Control Card 14
- Power Supply 14
- Allowable Gate Mass 15
- 5. Product Identification 16
- FIGURE 3C. WALL ADAPTOR KIT 17
- FIGURE 3D. HIGH-SECURITY KIT 17
- FIGURE 3E. MECHANO KIT 17
- FIGURE 3F. GATE ADAPTOR KIT 17
- FIGURE 4 18
- 7. Preparation of Site 19
- Strength of the Pillar 20
- FIGURE 8 21
- FIGURE 9 21
- FIGURE 10 21
- FIGURE 11 21
- FIGURE 14 22
- FIGURE 12 22
- FIGURE 13 22
- FIGURE 18 23
- FIGURE 15 23
- FIGURE 16 23
- FIGURE 17 23
- 8. Cabling Requirements 26
- 10. Operator Installation 28
- Determine the Gate Bracket 29
- Position 29
- FIGURE 35 30
- FIGURE 34 30
- FIGURE 36 30
- Fasten Gate Bracket to Gate 31
- Adjust Origin Clamp 32
- Gate closed 33
- Gate open 33
- For V400 (400mm operator) 34
- For V500 (500mm operator) 35
- Outward Swing Gate Setup 36
- FIGURE 53 37
- FIGURE 54 37
- FIGURE 55 38
- FIGURE 56 38
- FIGURE 57 39
- FIGURE 58 39
- 12. Allowable Wind Load 40
- Secure Control Box to Wall 41
- Connect all Wiring 41
- Setting the Limits 42
- FIGURE 65 43
- Master Motor (MTR M) 48
- Slave Motor (MTR S) 49
- Fuse protection 50
- 21. Solar Panel Wiring 51
- FIGURE 74. VIEW OF CONTROLLER 52
- 23. Menu Navigation Map 53
- 24. Controller Features 56
- Menu 4 - Modes of Operation 57
- Menu 5 - Run Profile 57
- FIGURE 78 58
- FIGURE 77 58
- FIGURE 76 58
- FIGURE 75 58
- Menu 6 59
- IR beams 59
- FIGURE 80 60
- FIGURE 81 61
- FIGURE 82 61
- Menu 7 - Pedestrian Opening 62
- Menu 8 - Gate Lock 63
- Menu 10 - General Features 64
- Menu 11 - Remote Controls 65
- 25. Factory Defaults Schedule 67
- CE Standard Profile 69
- UL325 Standard Profile 71
- 27. Diagnostics 76
- LCD Display 77
- Buzzer Feedback 78
- 28. Installation Handover 79
- Head Office: +27 11 699 2400 82
- +27 11 699 2481 82
Related products and manuals for Garden tools Centurion VECTOR2
Garden tools Centurion D3 User's Guide
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 0.556 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals