Centurion VECTOR2 Installation Manual Page 59
- Page / 82
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Inside
Closing Beam
Gates will not close
Outside
Closing Beam
Page 55
9. Pre-close Delay
Allows a delay between a valid trigger signal being received and the gate
commencing movement in the closing direction. The delay will also occur if
the gate is set to close automatically. A Warning Light can be set to activate
during this delay. (Refer to Pre-flash Modes of the feature ‘Pillar Light’, for
more details). This setting applies to both operators.
10. Opening Speed
Sets the maximum piston opening speed in millimeters per second.
This setting applies to both operators.
11. Closing Speed
Sets the maximum piston closing speed in millimeters per second.
This setting applies to both operators.
12. Ramp-up Distance
Sets the Ramp-up Distance in millimeters of travel of the piston when
starting. This setting applies to both operators.
13. Ramp-down Distance
Sets the Ramp-down Distance in millimeters of travel of the piston when
stopping. This setting applies to both operators.
14. Crawl Distance
Sets the final Crawl Distance in millimeters of travel of the piston when
reaching an endpoint. This setting applies to both operators.
15. Push Force Limit
Sets the maximum push force delivered by the operators. The maximum
setting is a value of 15 and the minimum is four. This is useful in cases where
limited push force is required. This setting applies to both operators.
Menu 6 -
IR beams
In a swing gate installation, in order
to provide protection to a person or
vehicle moving through the entrance,
it is necessary to have two sets of
Safety Beams, one across the
driveway where the gates are closed
and another where the gates are
open. Both sets of Safety Beams must
be set as Closing Safety Beams,
preventing the gate from closing and
stopping the gates if they have
started to close.
However, across the line of the
driveway up to where the gates open,
it is also recommended to have
another set of Safety Beams to
prevent the gate from opening if they
are closed and stop if they are
opening.
FIGURE 79
- SWING GATE 1
- OPERATORS 1
- Company Profile 2
- Contents 3
- Mechanical Setup 5
- Electrical Setup 6
- Commissioning 6
- IMPORTANT 7
- 1. Declaration of Conformity 9
- 2. General Description 10
- 3. Icons Used in this Manual 11
- 4. Specifications 12
- VECTOR2 400 VECTOR2 500 13
- Technical Specifications 13
- Control Card 14
- Power Supply 14
- Allowable Gate Mass 15
- 5. Product Identification 16
- FIGURE 3C. WALL ADAPTOR KIT 17
- FIGURE 3D. HIGH-SECURITY KIT 17
- FIGURE 3E. MECHANO KIT 17
- FIGURE 3F. GATE ADAPTOR KIT 17
- FIGURE 4 18
- 7. Preparation of Site 19
- Strength of the Pillar 20
- FIGURE 8 21
- FIGURE 9 21
- FIGURE 10 21
- FIGURE 11 21
- FIGURE 14 22
- FIGURE 12 22
- FIGURE 13 22
- FIGURE 18 23
- FIGURE 15 23
- FIGURE 16 23
- FIGURE 17 23
- 8. Cabling Requirements 26
- 10. Operator Installation 28
- Determine the Gate Bracket 29
- Position 29
- FIGURE 35 30
- FIGURE 34 30
- FIGURE 36 30
- Fasten Gate Bracket to Gate 31
- Adjust Origin Clamp 32
- Gate closed 33
- Gate open 33
- For V400 (400mm operator) 34
- For V500 (500mm operator) 35
- Outward Swing Gate Setup 36
- FIGURE 53 37
- FIGURE 54 37
- FIGURE 55 38
- FIGURE 56 38
- FIGURE 57 39
- FIGURE 58 39
- 12. Allowable Wind Load 40
- Secure Control Box to Wall 41
- Connect all Wiring 41
- Setting the Limits 42
- FIGURE 65 43
- Master Motor (MTR M) 48
- Slave Motor (MTR S) 49
- Fuse protection 50
- 21. Solar Panel Wiring 51
- FIGURE 74. VIEW OF CONTROLLER 52
- 23. Menu Navigation Map 53
- 24. Controller Features 56
- Menu 4 - Modes of Operation 57
- Menu 5 - Run Profile 57
- FIGURE 78 58
- FIGURE 77 58
- FIGURE 76 58
- FIGURE 75 58
- Menu 6 59
- IR beams 59
- FIGURE 80 60
- FIGURE 81 61
- FIGURE 82 61
- Menu 7 - Pedestrian Opening 62
- Menu 8 - Gate Lock 63
- Menu 10 - General Features 64
- Menu 11 - Remote Controls 65
- 25. Factory Defaults Schedule 67
- CE Standard Profile 69
- UL325 Standard Profile 71
- 27. Diagnostics 76
- LCD Display 77
- Buzzer Feedback 78
- 28. Installation Handover 79
- Head Office: +27 11 699 2400 82
- +27 11 699 2481 82
Related products and manuals for Garden tools Centurion VECTOR2
Garden tools Centurion D3 User's Guide
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 0.162 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals