Centurion VECTOR2 Installation Manual Page 74
- Page / 82
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
TRG Trigger input. (A normally-open potential-free input.) Momentarily
connecting this input to Com will cause the gate to open or close
depending on the operating mode selected. For more information see the
Autoclose feature and Modes of Operation.
PED Pedestrian Opening input. (A normally-open potential-free input.)
Momentarily connecting this input to Com will cause one gate to open to
the Pedestrian open position. For more information refer to the Pedestrian
feature.
FRX Free-exit input. (A normally-open potential-free input.) Momentarily
connecting this input to Com will cause a gate which is closed, or closing,
to open or re-open. If the gate is open, or opening, the signal has no
effect other than to reset the Autoclose Timer (if selected.) Free-exit (FRX)
never initiates a closing cycle. The only way to close a gate, if only the
FRX input is used, is to activate the Autoclose feature on the controller.
LIT LIT Activates the Pillar Light output. (A normally-open potential-free
input.) Momentarily connecting this input to Com will cause the LIGHT
relay to energise for a period of time as set in the Courtesy Light Timer
menu. If the connection is made for a period exceeding 3 seconds the
Pillar Light Relay will latch and remain latched indefinitely until a new
momentary connection to Com is given.
LED External gate status indicator. (A low-current output signal.) An output
terminal which provides a low-current drive (approx. 4.5V DC, 20mA) to a
LED which can be used to indicate the gate status remotely. If more than
three LEDs are required it is necessary to fit the CP78 MULTI-LED driver
card. For more details on the feedback about the status of the gate
provided by the Status LED refer to page 72.
Com The Common termination point. All trigger signals etc. have their return
path to one of the Com terminals.
Aux 12V Auxiliary power connection. Provides a +12V DC supply for auxiliary
equipment such as a radio receiver, Safety Beams, etc. It is linked directly
to the battery positive via a 3A resettable fuse.
Safe Com Used for switching the power supply to the safety beam. If automatic
beam testing is required, the negative power supply connection of the
beam transmitter must be wired to this point.
Sol Solenoid strike or magnetic lock. A solenoid strike lock or magnetic lock
can be connected between 12V and Sol. Note that the maximum current
draw allowed for the lock is 2A. Should the solenoid lock or magnetic lock
exceed this current rating it is necessary to use an interposing relay.
Particularly with magnetic locks, ensure that the steady state
current draw calculated over a 24 hour period and added to this,
the quiescent current draw of the controller, other peripherals and
the usage of the motors, does not exceed the current delivered
by the charger. If necessary, fit a separate supply to power the
lock using an interposing relay connected to the Sol input.
Page 70
- SWING GATE 1
- OPERATORS 1
- Company Profile 2
- Contents 3
- Mechanical Setup 5
- Electrical Setup 6
- Commissioning 6
- IMPORTANT 7
- 1. Declaration of Conformity 9
- 2. General Description 10
- 3. Icons Used in this Manual 11
- 4. Specifications 12
- VECTOR2 400 VECTOR2 500 13
- Technical Specifications 13
- Control Card 14
- Power Supply 14
- Allowable Gate Mass 15
- 5. Product Identification 16
- FIGURE 3C. WALL ADAPTOR KIT 17
- FIGURE 3D. HIGH-SECURITY KIT 17
- FIGURE 3E. MECHANO KIT 17
- FIGURE 3F. GATE ADAPTOR KIT 17
- FIGURE 4 18
- 7. Preparation of Site 19
- Strength of the Pillar 20
- FIGURE 8 21
- FIGURE 9 21
- FIGURE 10 21
- FIGURE 11 21
- FIGURE 14 22
- FIGURE 12 22
- FIGURE 13 22
- FIGURE 18 23
- FIGURE 15 23
- FIGURE 16 23
- FIGURE 17 23
- 8. Cabling Requirements 26
- 10. Operator Installation 28
- Determine the Gate Bracket 29
- Position 29
- FIGURE 35 30
- FIGURE 34 30
- FIGURE 36 30
- Fasten Gate Bracket to Gate 31
- Adjust Origin Clamp 32
- Gate closed 33
- Gate open 33
- For V400 (400mm operator) 34
- For V500 (500mm operator) 35
- Outward Swing Gate Setup 36
- FIGURE 53 37
- FIGURE 54 37
- FIGURE 55 38
- FIGURE 56 38
- FIGURE 57 39
- FIGURE 58 39
- 12. Allowable Wind Load 40
- Secure Control Box to Wall 41
- Connect all Wiring 41
- Setting the Limits 42
- FIGURE 65 43
- Master Motor (MTR M) 48
- Slave Motor (MTR S) 49
- Fuse protection 50
- 21. Solar Panel Wiring 51
- FIGURE 74. VIEW OF CONTROLLER 52
- 23. Menu Navigation Map 53
- 24. Controller Features 56
- Menu 4 - Modes of Operation 57
- Menu 5 - Run Profile 57
- FIGURE 78 58
- FIGURE 77 58
- FIGURE 76 58
- FIGURE 75 58
- Menu 6 59
- IR beams 59
- FIGURE 80 60
- FIGURE 81 61
- FIGURE 82 61
- Menu 7 - Pedestrian Opening 62
- Menu 8 - Gate Lock 63
- Menu 10 - General Features 64
- Menu 11 - Remote Controls 65
- 25. Factory Defaults Schedule 67
- CE Standard Profile 69
- UL325 Standard Profile 71
- 27. Diagnostics 76
- LCD Display 77
- Buzzer Feedback 78
- 28. Installation Handover 79
- Head Office: +27 11 699 2400 82
- +27 11 699 2481 82
Related products and manuals for Garden tools Centurion VECTOR2
Garden tools Centurion D3 User's Guide
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 2.410 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals