Centurion VECTOR2 Installation Manual Page 63
- Page / 82
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Page 59
Menu 8 - Gate Lock
A solenoid strike lock or magnetic lock can be connected to the control card,
allowing the gate to be locked when closed, open or both.
1. Lock enable status
Turns the lock functionality on or off.
2. Lock type
Allows selection of either a solenoid strike lock, or a magnetic lock. A solenoid
strike unlocks when power is applied, while a magnetic lock unlocks when
power is removed.
3. Release time
Sets the Time-period (in seconds) for which the lock remains released after
the gate has started moving.
A. Pre-Release time
Sets the Time-period (in 0.1 second increments) for which the lock
releases BEFORE the gate has started moving. This is useful in cases
where premature gate movement prevents the lock from releasing.
B. Lock location
Specifies whether the gate is locked while closed, open or both.
C. Lock drive
Specifies if the lock is to be powered by an AC or DC voltage.
Selecting AC will power the lock with a 50Hz square wave.
Menu 9 - Courtesy/Pillar Light
This feature is associated with the Light connections on the controller. Refer to
Section 16 of the manual for details on how to connect a Pillar or security Light
to the controller.
The Pillar Light circuit has multiple functions:
It operates as a Courtesy Light and switches on for a selectable time period
every time the gate is activated
The Courtesy Light can also be turned on for the same time period by
momentarily connecting the Aux 12V terminal to the Com terminal via a
pushbutton
The Courtesy Light can also be turned on permanently by connecting the Aux
12V terminal to the Com terminal via a pushbutton, for three seconds. A short
pulse thereafter will switch the lights off. The status LED will flash once every
two seconds to indicate that the Courtesy Light is on permanently.
The abovementioned facility can also be achieved via a remote learned to the
system and mapped to the Courtesy Light function from within the remotes
menu
The gate will not open when using the Aux 12V trigger input.
When the PED input is triggered, the Courtesy Light flashes for an adjustable
pre-flash time (1 to 255 seconds), before the pedestrian gate opens
- SWING GATE 1
- OPERATORS 1
- Company Profile 2
- Contents 3
- Mechanical Setup 5
- Electrical Setup 6
- Commissioning 6
- IMPORTANT 7
- 1. Declaration of Conformity 9
- 2. General Description 10
- 3. Icons Used in this Manual 11
- 4. Specifications 12
- VECTOR2 400 VECTOR2 500 13
- Technical Specifications 13
- Control Card 14
- Power Supply 14
- Allowable Gate Mass 15
- 5. Product Identification 16
- FIGURE 3C. WALL ADAPTOR KIT 17
- FIGURE 3D. HIGH-SECURITY KIT 17
- FIGURE 3E. MECHANO KIT 17
- FIGURE 3F. GATE ADAPTOR KIT 17
- FIGURE 4 18
- 7. Preparation of Site 19
- Strength of the Pillar 20
- FIGURE 8 21
- FIGURE 9 21
- FIGURE 10 21
- FIGURE 11 21
- FIGURE 14 22
- FIGURE 12 22
- FIGURE 13 22
- FIGURE 18 23
- FIGURE 15 23
- FIGURE 16 23
- FIGURE 17 23
- 8. Cabling Requirements 26
- 10. Operator Installation 28
- Determine the Gate Bracket 29
- Position 29
- FIGURE 35 30
- FIGURE 34 30
- FIGURE 36 30
- Fasten Gate Bracket to Gate 31
- Adjust Origin Clamp 32
- Gate closed 33
- Gate open 33
- For V400 (400mm operator) 34
- For V500 (500mm operator) 35
- Outward Swing Gate Setup 36
- FIGURE 53 37
- FIGURE 54 37
- FIGURE 55 38
- FIGURE 56 38
- FIGURE 57 39
- FIGURE 58 39
- 12. Allowable Wind Load 40
- Secure Control Box to Wall 41
- Connect all Wiring 41
- Setting the Limits 42
- FIGURE 65 43
- Master Motor (MTR M) 48
- Slave Motor (MTR S) 49
- Fuse protection 50
- 21. Solar Panel Wiring 51
- FIGURE 74. VIEW OF CONTROLLER 52
- 23. Menu Navigation Map 53
- 24. Controller Features 56
- Menu 4 - Modes of Operation 57
- Menu 5 - Run Profile 57
- FIGURE 78 58
- FIGURE 77 58
- FIGURE 76 58
- FIGURE 75 58
- Menu 6 59
- IR beams 59
- FIGURE 80 60
- FIGURE 81 61
- FIGURE 82 61
- Menu 7 - Pedestrian Opening 62
- Menu 8 - Gate Lock 63
- Menu 10 - General Features 64
- Menu 11 - Remote Controls 65
- 25. Factory Defaults Schedule 67
- CE Standard Profile 69
- UL325 Standard Profile 71
- 27. Diagnostics 76
- LCD Display 77
- Buzzer Feedback 78
- 28. Installation Handover 79
- Head Office: +27 11 699 2400 82
- +27 11 699 2481 82
Related products and manuals for Garden tools Centurion VECTOR2
Garden tools Centurion D3 User's Guide
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 0.507 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals