Centurion VECTOR2 Installation Manual Page 73
- Page / 82
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
S Sens1 Slave Motor (MTR S). Connects to the thin PURPLE wire of the
Slave Motor.
S Sens2 Slave Motor (MTR S). Connects to the thin BLUE or ORANGE wire of the
Slave Motor.
M Sens1 Master Motor (MTR M). Connects to the thin PURPLE wire of the
Master Motor.
M Sens2 Master Motor (MTR M). Connects to the thin BLUE or ORANGE wire of
the Master Motor.
Sens + Operator sensor power connection. A 5V output for connecting to the thin
RED sensor wire on both the MTR M and MTR S operators.
Sens - Operator sensor power connection. A 0V output for connecting to the thin
BLACK or GREY sensor wire on both the MTR M and MTR S operators.
Safe CLS Closing edge safety input. (A normally-closed potential-free input.)
As long as a connection between this input and Com is maintained the
controller will behave normally. When this connection is broken it will
prevent the gate from closing if it is stationary, and will stop and reverse
the gate if it is closing. This input has no effect if the gate is opening.
If the Safe CLS function is not required a link must be fitted
between Safe CLS and Com for the controller to operate
normally.
Safe OPN Opening edge safety input. (A normally-closed potential-free input.)
For as long as a connection between this input and Com is maintained the
controller will behave normally. When this connection is broken it will
prevent the gate from opening if it is stationary, and will stop and reverse
the gate if it is opening. This input has no effect if the gate is closing.
If the Safe Open and reverse functions are not required a link
must be fitted between safe Open and Com for the controller to
operate normally.
26. Description of Terminal Functions
Page 69
LCK/STP Holiday Lockout or gate stop input. (A normally-closed potential-free
input.) For as long as a connection between this input and Com is
maintained the controller will behave normally. But, when this connection
to Com is broken all inputs are inhibited, and if the gate is moving it will
stop.
If the LCK function is not required a link must be fitted between
LCK and Com.
When setting up the controller for the first time or after a full reset back to the Factory Default
has been performed, the system will electronically override the Safety Inputs and allow the
system to function without the links. However if safeties are connected to either or both inputs,
thereafter there must be a normally-closed circuit maintained for the system to operate
correctly. I.e. if Safety Beams are fitted and then removed, the circuit which is affected must be
replaced with a wire link to create a normally-closed circuit.
- SWING GATE 1
- OPERATORS 1
- Company Profile 2
- Contents 3
- Mechanical Setup 5
- Electrical Setup 6
- Commissioning 6
- IMPORTANT 7
- 1. Declaration of Conformity 9
- 2. General Description 10
- 3. Icons Used in this Manual 11
- 4. Specifications 12
- VECTOR2 400 VECTOR2 500 13
- Technical Specifications 13
- Control Card 14
- Power Supply 14
- Allowable Gate Mass 15
- 5. Product Identification 16
- FIGURE 3C. WALL ADAPTOR KIT 17
- FIGURE 3D. HIGH-SECURITY KIT 17
- FIGURE 3E. MECHANO KIT 17
- FIGURE 3F. GATE ADAPTOR KIT 17
- FIGURE 4 18
- 7. Preparation of Site 19
- Strength of the Pillar 20
- FIGURE 8 21
- FIGURE 9 21
- FIGURE 10 21
- FIGURE 11 21
- FIGURE 14 22
- FIGURE 12 22
- FIGURE 13 22
- FIGURE 18 23
- FIGURE 15 23
- FIGURE 16 23
- FIGURE 17 23
- 8. Cabling Requirements 26
- 10. Operator Installation 28
- Determine the Gate Bracket 29
- Position 29
- FIGURE 35 30
- FIGURE 34 30
- FIGURE 36 30
- Fasten Gate Bracket to Gate 31
- Adjust Origin Clamp 32
- Gate closed 33
- Gate open 33
- For V400 (400mm operator) 34
- For V500 (500mm operator) 35
- Outward Swing Gate Setup 36
- FIGURE 53 37
- FIGURE 54 37
- FIGURE 55 38
- FIGURE 56 38
- FIGURE 57 39
- FIGURE 58 39
- 12. Allowable Wind Load 40
- Secure Control Box to Wall 41
- Connect all Wiring 41
- Setting the Limits 42
- FIGURE 65 43
- Master Motor (MTR M) 48
- Slave Motor (MTR S) 49
- Fuse protection 50
- 21. Solar Panel Wiring 51
- FIGURE 74. VIEW OF CONTROLLER 52
- 23. Menu Navigation Map 53
- 24. Controller Features 56
- Menu 4 - Modes of Operation 57
- Menu 5 - Run Profile 57
- FIGURE 78 58
- FIGURE 77 58
- FIGURE 76 58
- FIGURE 75 58
- Menu 6 59
- IR beams 59
- FIGURE 80 60
- FIGURE 81 61
- FIGURE 82 61
- Menu 7 - Pedestrian Opening 62
- Menu 8 - Gate Lock 63
- Menu 10 - General Features 64
- Menu 11 - Remote Controls 65
- 25. Factory Defaults Schedule 67
- CE Standard Profile 69
- UL325 Standard Profile 71
- 27. Diagnostics 76
- LCD Display 77
- Buzzer Feedback 78
- 28. Installation Handover 79
- Head Office: +27 11 699 2400 82
- +27 11 699 2481 82
Related products and manuals for Garden tools Centurion VECTOR2
Garden tools Centurion D3 User's Guide
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 2.204 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals