Centurion VECTOR2 Installation Manual Page 60
- Page / 82
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Page 56
Two independent normally-closed inputs are provided for Opening and Closing
Safety Beams.
An interrupted closing beam will prevent the gates from closing and stop and
reverse the gates back to the open position if already opening. Vice-versa for an
opening beam.
Additional beam functionality is provided:
1. PIRAC Autoclose
The Passive-Infrared Autoclose
feature allows the gate to close
automatically, as soon as a vehicle
or pedestrian has passed through
the closing beam. This security
feature ensures that the gate stays
open for the minimum amount of
time possible.
If the Autoclose feature has been
enabled, the system will react in
the following way:
When the gate is triggered to
open and nothing moves
Outside Closing Beam
Inside Closing Beam
Opening Beam
IRBO = IRBC
(Combine inside Closing Beam with
Opening Beam = save on one beam)
FIGURE 80
through or interrupts the closing beam, the gate will open fully and stay
open for the period of time determined by the Autoclose TIMER
However, if the closing beam is interrupted at any stage, while the gate is
opening or open, the gate will close immediately after the closing beam is
cleared
If the Autoclose feature has not been enabled then the gate will remain
open indefinitely. To close the gate the closing beam must be interrupted
or the trigger button must be pressed.
2. Safe Output Status
Automatically tests the Safety Beams before each gate cycle. (E.g. as
required by CE and UL325)
In order for this feature to work, the power supply negative of the beam
transmitter must be wired to the Safe Com terminal of the controller.
The time taken for the gate to open again after it has come to a stop is
approximately three seconds
Example:
Autoclose Override time set to five seconds: Total time to temporarily
disable the PIRAC feature is approximately eight seconds
(5s + 3s = 8 seconds)
- SWING GATE 1
- OPERATORS 1
- Company Profile 2
- Contents 3
- Mechanical Setup 5
- Electrical Setup 6
- Commissioning 6
- IMPORTANT 7
- 1. Declaration of Conformity 9
- 2. General Description 10
- 3. Icons Used in this Manual 11
- 4. Specifications 12
- VECTOR2 400 VECTOR2 500 13
- Technical Specifications 13
- Control Card 14
- Power Supply 14
- Allowable Gate Mass 15
- 5. Product Identification 16
- FIGURE 3C. WALL ADAPTOR KIT 17
- FIGURE 3D. HIGH-SECURITY KIT 17
- FIGURE 3E. MECHANO KIT 17
- FIGURE 3F. GATE ADAPTOR KIT 17
- FIGURE 4 18
- 7. Preparation of Site 19
- Strength of the Pillar 20
- FIGURE 8 21
- FIGURE 9 21
- FIGURE 10 21
- FIGURE 11 21
- FIGURE 14 22
- FIGURE 12 22
- FIGURE 13 22
- FIGURE 18 23
- FIGURE 15 23
- FIGURE 16 23
- FIGURE 17 23
- 8. Cabling Requirements 26
- 10. Operator Installation 28
- Determine the Gate Bracket 29
- Position 29
- FIGURE 35 30
- FIGURE 34 30
- FIGURE 36 30
- Fasten Gate Bracket to Gate 31
- Adjust Origin Clamp 32
- Gate closed 33
- Gate open 33
- For V400 (400mm operator) 34
- For V500 (500mm operator) 35
- Outward Swing Gate Setup 36
- FIGURE 53 37
- FIGURE 54 37
- FIGURE 55 38
- FIGURE 56 38
- FIGURE 57 39
- FIGURE 58 39
- 12. Allowable Wind Load 40
- Secure Control Box to Wall 41
- Connect all Wiring 41
- Setting the Limits 42
- FIGURE 65 43
- Master Motor (MTR M) 48
- Slave Motor (MTR S) 49
- Fuse protection 50
- 21. Solar Panel Wiring 51
- FIGURE 74. VIEW OF CONTROLLER 52
- 23. Menu Navigation Map 53
- 24. Controller Features 56
- Menu 4 - Modes of Operation 57
- Menu 5 - Run Profile 57
- FIGURE 78 58
- FIGURE 77 58
- FIGURE 76 58
- FIGURE 75 58
- Menu 6 59
- IR beams 59
- FIGURE 80 60
- FIGURE 81 61
- FIGURE 82 61
- Menu 7 - Pedestrian Opening 62
- Menu 8 - Gate Lock 63
- Menu 10 - General Features 64
- Menu 11 - Remote Controls 65
- 25. Factory Defaults Schedule 67
- CE Standard Profile 69
- UL325 Standard Profile 71
- 27. Diagnostics 76
- LCD Display 77
- Buzzer Feedback 78
- 28. Installation Handover 79
- Head Office: +27 11 699 2400 82
- +27 11 699 2481 82
Related products and manuals for Garden tools Centurion VECTOR2
Garden tools Centurion D3 User's Guide
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 0.303 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals