Centurion VECTOR2 Installation Manual Page 10
- Page / 82
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
2. General Description
Page 6
The VECTOR2 operator has been designed to safely and cost-effectively automate a wide
variety of swing gates, from single light-domestic swing gates to heavy industrial double
swing gates.
The fail-safe and fully redundant Position and Collision Detection system has been
designed and tested to set the standard in safety of operation and to provide an
unparalleled level of reliability and durability in operation.
The gate Travel Limits are managed by a sealed double-redundant opto-electronic system
that has been designed not only to ensure ultra-reliable operation, but also to ensure
precise position and trajectory control. This enables very accurate and reliable collision
detection to ensure safe operation even under trying conditions.
The VECTOR2 control card has been designed to be easy and intuitive to use, with
helpful instructions on the status of the operation being given both during and after the
installation. It also has a built-in diagnostic procedure that can verify every aspect of the
control card onsite.
Some of the advanced features offered by the VECTOR2 controller are:
Fully automated single-button Limit Setup for single and double swing gates
Full graphics LCD display provides an intuitive user interface with built-in diagnostics to
speed up and simplify the installation process
Separate safety inputs for infrared beams on both the closing and opening directions of
the gate
Advanced closed-loop speed control to maintain safe and reliable operation on inclined
gates under windy conditions
Fully configurable gate Run Profiles
Selectable and adjustable Autoclose with pushbutton override
Pedestrian (Partial) opening with automatic closure
Free-exit input
Positive Close Mode
Multiple Modes of Operation
Solenoid lock drive output up to 2A
Holiday Lockout
A status LED output to indicate the gate status remotely
Pillar Light control
Leaf delay is selectable for either gate leaf
Onboard CENTURION receiver with selective adding and deleting of remotes
- SWING GATE 1
- OPERATORS 1
- Company Profile 2
- Contents 3
- Mechanical Setup 5
- Electrical Setup 6
- Commissioning 6
- IMPORTANT 7
- 1. Declaration of Conformity 9
- 2. General Description 10
- 3. Icons Used in this Manual 11
- 4. Specifications 12
- VECTOR2 400 VECTOR2 500 13
- Technical Specifications 13
- Control Card 14
- Power Supply 14
- Allowable Gate Mass 15
- 5. Product Identification 16
- FIGURE 3C. WALL ADAPTOR KIT 17
- FIGURE 3D. HIGH-SECURITY KIT 17
- FIGURE 3E. MECHANO KIT 17
- FIGURE 3F. GATE ADAPTOR KIT 17
- FIGURE 4 18
- 7. Preparation of Site 19
- Strength of the Pillar 20
- FIGURE 8 21
- FIGURE 9 21
- FIGURE 10 21
- FIGURE 11 21
- FIGURE 14 22
- FIGURE 12 22
- FIGURE 13 22
- FIGURE 18 23
- FIGURE 15 23
- FIGURE 16 23
- FIGURE 17 23
- 8. Cabling Requirements 26
- 10. Operator Installation 28
- Determine the Gate Bracket 29
- Position 29
- FIGURE 35 30
- FIGURE 34 30
- FIGURE 36 30
- Fasten Gate Bracket to Gate 31
- Adjust Origin Clamp 32
- Gate closed 33
- Gate open 33
- For V400 (400mm operator) 34
- For V500 (500mm operator) 35
- Outward Swing Gate Setup 36
- FIGURE 53 37
- FIGURE 54 37
- FIGURE 55 38
- FIGURE 56 38
- FIGURE 57 39
- FIGURE 58 39
- 12. Allowable Wind Load 40
- Secure Control Box to Wall 41
- Connect all Wiring 41
- Setting the Limits 42
- FIGURE 65 43
- Master Motor (MTR M) 48
- Slave Motor (MTR S) 49
- Fuse protection 50
- 21. Solar Panel Wiring 51
- FIGURE 74. VIEW OF CONTROLLER 52
- 23. Menu Navigation Map 53
- 24. Controller Features 56
- Menu 4 - Modes of Operation 57
- Menu 5 - Run Profile 57
- FIGURE 78 58
- FIGURE 77 58
- FIGURE 76 58
- FIGURE 75 58
- Menu 6 59
- IR beams 59
- FIGURE 80 60
- FIGURE 81 61
- FIGURE 82 61
- Menu 7 - Pedestrian Opening 62
- Menu 8 - Gate Lock 63
- Menu 10 - General Features 64
- Menu 11 - Remote Controls 65
- 25. Factory Defaults Schedule 67
- CE Standard Profile 69
- UL325 Standard Profile 71
- 27. Diagnostics 76
- LCD Display 77
- Buzzer Feedback 78
- 28. Installation Handover 79
- Head Office: +27 11 699 2400 82
- +27 11 699 2481 82
Related products and manuals for Garden tools Centurion VECTOR2
Garden tools Centurion D3 User's Guide
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 0.957 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals