Centurion VECTOR2 Installation Manual Page 62
- Page / 82
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Page 58
D. Alarm output
The system can be configured to operate one of the following outputs
provided on the controller:
Onboard buzzer - emits a continuous tone
Pillar / Courtesy Light contact (potential-free normally-open contact,
fuse-protected - 5A)
Aux IO (this is an open collector drive, maximum current draw 3A, not
fuse-protected)
Safety beam common (this is an open collector drive, maximum current
draw 3A, not fuse-protected)
Status LED output (operate up to three LEDs in parallel or interface with
the CP78 MULTI-LED driver card)
Menu 7 - Pedestrian Opening
This feature is associated with the PED input on the controller. When activating
this input, the system will open the gate to the Pedestrian Open position, and
then automatically close after the Pedestrian Autoclose time lapses. If the PED
connection to Com is maintained, then the gate will remain open, and when the
connection is broken, it will close after the Pedestrian Autoclose time has
expired.
The time taken for the gate to open to pedestrian is dependent on the pedestrian
Pre-open Delay and the time required for the gate to close from the pedestrian
position is dependent on the Pedestrian Pre-close Delay.
The Warning Light is any light wired to the Pillar Light contacts, as
described in Menu 9.
1. Pedestrian Open Position
Sets the maximum opening of the pedestrian gate in metres, in one
centimetre steps.
2. Pedestrian Autoclose Time
Sets the Autoclose time in seconds after a Pedestrian Opening. This time can
be set from zero seconds to four minutes in one second steps.
3. Pedestrian Pre-open Delay
Sets the time delay between the pedestrian input being activated, and the
gate actually opening. This enhances safety in cases where the pedestrian
has to reach through the gate in order to activate the pedestrian input.
A Warning Light would typically be active during this delay. This delay can be
set from zero seconds to four minutes in one second steps.
4. Pedestrian Pre-close Delay
Sets the time delay between the Pedestrian Autoclose timer expiring, and the
gate actually closing. A Warning Light would typically be active during this
delay. This delay can be set from zero seconds to four minutes in one second
steps.
- SWING GATE 1
- OPERATORS 1
- Company Profile 2
- Contents 3
- Mechanical Setup 5
- Electrical Setup 6
- Commissioning 6
- IMPORTANT 7
- 1. Declaration of Conformity 9
- 2. General Description 10
- 3. Icons Used in this Manual 11
- 4. Specifications 12
- VECTOR2 400 VECTOR2 500 13
- Technical Specifications 13
- Control Card 14
- Power Supply 14
- Allowable Gate Mass 15
- 5. Product Identification 16
- FIGURE 3C. WALL ADAPTOR KIT 17
- FIGURE 3D. HIGH-SECURITY KIT 17
- FIGURE 3E. MECHANO KIT 17
- FIGURE 3F. GATE ADAPTOR KIT 17
- FIGURE 4 18
- 7. Preparation of Site 19
- Strength of the Pillar 20
- FIGURE 8 21
- FIGURE 9 21
- FIGURE 10 21
- FIGURE 11 21
- FIGURE 14 22
- FIGURE 12 22
- FIGURE 13 22
- FIGURE 18 23
- FIGURE 15 23
- FIGURE 16 23
- FIGURE 17 23
- 8. Cabling Requirements 26
- 10. Operator Installation 28
- Determine the Gate Bracket 29
- Position 29
- FIGURE 35 30
- FIGURE 34 30
- FIGURE 36 30
- Fasten Gate Bracket to Gate 31
- Adjust Origin Clamp 32
- Gate closed 33
- Gate open 33
- For V400 (400mm operator) 34
- For V500 (500mm operator) 35
- Outward Swing Gate Setup 36
- FIGURE 53 37
- FIGURE 54 37
- FIGURE 55 38
- FIGURE 56 38
- FIGURE 57 39
- FIGURE 58 39
- 12. Allowable Wind Load 40
- Secure Control Box to Wall 41
- Connect all Wiring 41
- Setting the Limits 42
- FIGURE 65 43
- Master Motor (MTR M) 48
- Slave Motor (MTR S) 49
- Fuse protection 50
- 21. Solar Panel Wiring 51
- FIGURE 74. VIEW OF CONTROLLER 52
- 23. Menu Navigation Map 53
- 24. Controller Features 56
- Menu 4 - Modes of Operation 57
- Menu 5 - Run Profile 57
- FIGURE 78 58
- FIGURE 77 58
- FIGURE 76 58
- FIGURE 75 58
- Menu 6 59
- IR beams 59
- FIGURE 80 60
- FIGURE 81 61
- FIGURE 82 61
- Menu 7 - Pedestrian Opening 62
- Menu 8 - Gate Lock 63
- Menu 10 - General Features 64
- Menu 11 - Remote Controls 65
- 25. Factory Defaults Schedule 67
- CE Standard Profile 69
- UL325 Standard Profile 71
- 27. Diagnostics 76
- LCD Display 77
- Buzzer Feedback 78
- 28. Installation Handover 79
- Head Office: +27 11 699 2400 82
- +27 11 699 2481 82
Related products and manuals for Garden tools Centurion VECTOR2
Garden tools Centurion D3 User's Guide
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 0.485 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals