Centurion VECTOR2 Installation Manual Page 65
- Page / 82
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Page 61
Menu 11 - Remote Controls
The controller is capable of learning up to 64 CENTURION code-hopping remote
controls. Each remote control can have up to four buttons. Each remote control
learned into the system is assigned a unique remote control ID.
It is possible to artificially increase the number of buttons of a multi-
button remote control by using a two-button combination
One of the buttons is used as a Shift Button to allow the other
buttons to be used again in combination with this button. In other
words, the user will press and hold the Shift Button, before pressing
one of the other buttons to create a new button
The Shift Button cannot be used as a button on its own, it must always
be used in combination with the other buttons
Benefits of the Shift Button system:
Use of the Shift Button system allows a three-button remote control
to gain an extra button and operate four functions and likewise a four-
button remote control gains two extra buttons and can operate six
functions
Another benefit of using the Shift Button system is that it requires
both hands to operate the two-button combination.
This prevents the user from accidentally enabling sensitive functions
such as Holiday Lockout on the controller
Each remote control learned into the system is assigned a unique
remote control ID
1. Press Valid Button
If the Remote Controls Menu has been locked as discussed later, only by
pressing a button of a remote control learned into the system, can the
Remote Controls Menu be accessed.
2. Add Remote
Any button can be set to control the Trigger, Pedestrian, Free-exit, Holiday
Lockout or Courtesy Light Control (Aux) inputs. When adding remote
controls, it is recommended that a record be kept of the ID number allocated
by the system to each respective remote control and the person to whom the
remote control is given. This is necessary should selective deletion be
required at a later stage.
3. Delete Remote
Remote controls can be deleted at any stage according to one of the following
methods:
A. Delete Remote by ID
Each remote control can be deleted individually according to its unique ID.
To facilitate this, a record of the ID and the person to whom the ID has
been assigned must have been made at the time of learning the
remote control into the system. The remote control is not required for this
operation.
- SWING GATE 1
- OPERATORS 1
- Company Profile 2
- Contents 3
- Mechanical Setup 5
- Electrical Setup 6
- Commissioning 6
- IMPORTANT 7
- 1. Declaration of Conformity 9
- 2. General Description 10
- 3. Icons Used in this Manual 11
- 4. Specifications 12
- VECTOR2 400 VECTOR2 500 13
- Technical Specifications 13
- Control Card 14
- Power Supply 14
- Allowable Gate Mass 15
- 5. Product Identification 16
- FIGURE 3C. WALL ADAPTOR KIT 17
- FIGURE 3D. HIGH-SECURITY KIT 17
- FIGURE 3E. MECHANO KIT 17
- FIGURE 3F. GATE ADAPTOR KIT 17
- FIGURE 4 18
- 7. Preparation of Site 19
- Strength of the Pillar 20
- FIGURE 8 21
- FIGURE 9 21
- FIGURE 10 21
- FIGURE 11 21
- FIGURE 14 22
- FIGURE 12 22
- FIGURE 13 22
- FIGURE 18 23
- FIGURE 15 23
- FIGURE 16 23
- FIGURE 17 23
- 8. Cabling Requirements 26
- 10. Operator Installation 28
- Determine the Gate Bracket 29
- Position 29
- FIGURE 35 30
- FIGURE 34 30
- FIGURE 36 30
- Fasten Gate Bracket to Gate 31
- Adjust Origin Clamp 32
- Gate closed 33
- Gate open 33
- For V400 (400mm operator) 34
- For V500 (500mm operator) 35
- Outward Swing Gate Setup 36
- FIGURE 53 37
- FIGURE 54 37
- FIGURE 55 38
- FIGURE 56 38
- FIGURE 57 39
- FIGURE 58 39
- 12. Allowable Wind Load 40
- Secure Control Box to Wall 41
- Connect all Wiring 41
- Setting the Limits 42
- FIGURE 65 43
- Master Motor (MTR M) 48
- Slave Motor (MTR S) 49
- Fuse protection 50
- 21. Solar Panel Wiring 51
- FIGURE 74. VIEW OF CONTROLLER 52
- 23. Menu Navigation Map 53
- 24. Controller Features 56
- Menu 4 - Modes of Operation 57
- Menu 5 - Run Profile 57
- FIGURE 78 58
- FIGURE 77 58
- FIGURE 76 58
- FIGURE 75 58
- Menu 6 59
- IR beams 59
- FIGURE 80 60
- FIGURE 81 61
- FIGURE 82 61
- Menu 7 - Pedestrian Opening 62
- Menu 8 - Gate Lock 63
- Menu 10 - General Features 64
- Menu 11 - Remote Controls 65
- 25. Factory Defaults Schedule 67
- CE Standard Profile 69
- UL325 Standard Profile 71
- 27. Diagnostics 76
- LCD Display 77
- Buzzer Feedback 78
- 28. Installation Handover 79
- Head Office: +27 11 699 2400 82
- +27 11 699 2481 82
Related products and manuals for Garden tools Centurion VECTOR2
Garden tools Centurion D3 User's Guide
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 1.158 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals