Centurion VECTOR2 Installation Manual Page 64
- Page / 82
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Page 60
1. Courtesy Light time
The time that the Courtesy Light will remain activated can be set from four
seconds to ten hours in one second increments.
2. Light profile
The Courtesy Light can be selected to operate according to one of the
following:
A. Courtesy Light as explained earlier
B. Pre-flashing Mode
If Pre-flashing Mode A, B or C is selected, the behaviour of the Courtesy Light
will be as follows:
Mode A will turn on the Courtesy Light only while the gate is moving
Mode B will flash the Courtesy Light during the Pre-opening and
Pre-closing Delays, as well as while the gate is moving
Mode C will turn on the Courtesy Light during the Pre-opening and
Pre-closing Delays, as well as while the gate is moving
In these Pre-flashing Modes, the timed Courtesy Light functionality is not
available
Menu 10 - General Features
1. Operator
This menu item allows the user to set the type of V-Series operator currently
being used with the controller. Always ensure that VECTOR is selected.
When not in Setup Mode, i.e. Normal Mode, the currently-enabled operator
will be displayed in the bottom left-hand corner of the LCD screen, with VC
indicating VECTOR.
2. Operating Standard
Regional Operating Standards can be set. Applying this setting will
automatically configure the controller settings to conform to the specific
region’s standard. (E.g. UL325 or CE.)
3. Reset Options
The controller settings can be reset through the Reset Options menu.
Various reset options are available:
A. Factory Defaults - All settings will be restored to the default values
dictated by the Operating Standard/Profile that is currently selected.
All remote controls and gate limits will not be affected.
B. Delete All Remotes - Delete all the remotes stored in the system; no
settings affected.
C. Reset All - Clears and defaults the system completely. The unit will be
reset to the Factory Default settings in addition to clearing all remotes and
time-periods.
4. Diagnostic Screen
Allows a diagnostic screen to be displayed. This can be useful when
troubleshooting, but requires some technical knowledge.
5. Round Test Button
Allows the round test button on the controller to be disabled, in cases where
higher security is required.
- SWING GATE 1
- OPERATORS 1
- Company Profile 2
- Contents 3
- Mechanical Setup 5
- Electrical Setup 6
- Commissioning 6
- IMPORTANT 7
- 1. Declaration of Conformity 9
- 2. General Description 10
- 3. Icons Used in this Manual 11
- 4. Specifications 12
- VECTOR2 400 VECTOR2 500 13
- Technical Specifications 13
- Control Card 14
- Power Supply 14
- Allowable Gate Mass 15
- 5. Product Identification 16
- FIGURE 3C. WALL ADAPTOR KIT 17
- FIGURE 3D. HIGH-SECURITY KIT 17
- FIGURE 3E. MECHANO KIT 17
- FIGURE 3F. GATE ADAPTOR KIT 17
- FIGURE 4 18
- 7. Preparation of Site 19
- Strength of the Pillar 20
- FIGURE 8 21
- FIGURE 9 21
- FIGURE 10 21
- FIGURE 11 21
- FIGURE 14 22
- FIGURE 12 22
- FIGURE 13 22
- FIGURE 18 23
- FIGURE 15 23
- FIGURE 16 23
- FIGURE 17 23
- 8. Cabling Requirements 26
- 10. Operator Installation 28
- Determine the Gate Bracket 29
- Position 29
- FIGURE 35 30
- FIGURE 34 30
- FIGURE 36 30
- Fasten Gate Bracket to Gate 31
- Adjust Origin Clamp 32
- Gate closed 33
- Gate open 33
- For V400 (400mm operator) 34
- For V500 (500mm operator) 35
- Outward Swing Gate Setup 36
- FIGURE 53 37
- FIGURE 54 37
- FIGURE 55 38
- FIGURE 56 38
- FIGURE 57 39
- FIGURE 58 39
- 12. Allowable Wind Load 40
- Secure Control Box to Wall 41
- Connect all Wiring 41
- Setting the Limits 42
- FIGURE 65 43
- Master Motor (MTR M) 48
- Slave Motor (MTR S) 49
- Fuse protection 50
- 21. Solar Panel Wiring 51
- FIGURE 74. VIEW OF CONTROLLER 52
- 23. Menu Navigation Map 53
- 24. Controller Features 56
- Menu 4 - Modes of Operation 57
- Menu 5 - Run Profile 57
- FIGURE 78 58
- FIGURE 77 58
- FIGURE 76 58
- FIGURE 75 58
- Menu 6 59
- IR beams 59
- FIGURE 80 60
- FIGURE 81 61
- FIGURE 82 61
- Menu 7 - Pedestrian Opening 62
- Menu 8 - Gate Lock 63
- Menu 10 - General Features 64
- Menu 11 - Remote Controls 65
- 25. Factory Defaults Schedule 67
- CE Standard Profile 69
- UL325 Standard Profile 71
- 27. Diagnostics 76
- LCD Display 77
- Buzzer Feedback 78
- 28. Installation Handover 79
- Head Office: +27 11 699 2400 82
- +27 11 699 2481 82
Related products and manuals for Garden tools Centurion VECTOR2
Garden tools Centurion D3 User's Guide
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 1.160 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals