Centurion VECTOR2 Installation Manual Page 58
- Page / 82
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Page 54
3. Short Stop
PCM applied to one gate is ideal for securely locking two gates to each other
without having to fit endstops. Typically, a 'mechanical' lip is fitted to one
gate which will push up against the other gate and via PCM keep pushing
until the gates are mechanically locked. To ensure that the gates do not close
past their desired end point, the Slave Gate against which the Master gate
with the mechanical lip pushes, can be preset to stop slightly short of its
closed position. This is referred to as the 'Short Stop' distance. If the 'Short
Stop' distance is correctly set, the Master Gate will engage with the Slave
Gate sufficiently before the closed position and via the PCM, push the two
gates into the fully closed position, but not past it.
4. Short Stop value
The Short Stop distance can be set
between 1mm and 40mm of
piston stroke.
5. PCM push force
The amount of force applied by
the actuator when in PCM can be
set as a value from 1 to 15.
6. Leaf Delay
Leaf Delay is used in cases where
one gate leaf must move before
the other. The most common need
for this arises when a mechanical
'lip' is fitted to one of the gates.
In a double leaf installation, a Leaf
Delay can be set whereby the
MTRM Motor will open before the
MTRS Motor and the MTRS Motor
will close before the MTRM Motor.
7. Leaf Delay value
The Leaf Delay is based on piston
position, and can be adjusted from
3mm to 250mm of piston travel.
8. Pre-open Delay
Allows a delay between a valid
trigger signal being received and
the gate commencing movement
in the opening direction.
A Warning Light can be set to
activate during this delay. (Refer
to Pre-flash Modes of the feature
‘Pillar Light’, for more details.)
This setting applies to both
motors.
FIGURE 78
Mechanical lip on
M Gate engages with S Gate
With PCM, Master Gate continues closing,
pushing the Slave Gate with it
FIGURE 77
FIGURE 76
MTRM Gate continues to close
‘Short Stop’
Slave Gate stops slightly before
closed position
Line of gates when closed
MTRM gate closes
slightly behind
MTRS Gate (Leaf delay)
MTRS Gate closes first
Mechanical lip
FIGURE 75
If ‘Short Stop’ is correctly set, PCM will cut
off when gates reach closed position, in line
- SWING GATE 1
- OPERATORS 1
- Company Profile 2
- Contents 3
- Mechanical Setup 5
- Electrical Setup 6
- Commissioning 6
- IMPORTANT 7
- 1. Declaration of Conformity 9
- 2. General Description 10
- 3. Icons Used in this Manual 11
- 4. Specifications 12
- VECTOR2 400 VECTOR2 500 13
- Technical Specifications 13
- Control Card 14
- Power Supply 14
- Allowable Gate Mass 15
- 5. Product Identification 16
- FIGURE 3C. WALL ADAPTOR KIT 17
- FIGURE 3D. HIGH-SECURITY KIT 17
- FIGURE 3E. MECHANO KIT 17
- FIGURE 3F. GATE ADAPTOR KIT 17
- FIGURE 4 18
- 7. Preparation of Site 19
- Strength of the Pillar 20
- FIGURE 8 21
- FIGURE 9 21
- FIGURE 10 21
- FIGURE 11 21
- FIGURE 14 22
- FIGURE 12 22
- FIGURE 13 22
- FIGURE 18 23
- FIGURE 15 23
- FIGURE 16 23
- FIGURE 17 23
- 8. Cabling Requirements 26
- 10. Operator Installation 28
- Determine the Gate Bracket 29
- Position 29
- FIGURE 35 30
- FIGURE 34 30
- FIGURE 36 30
- Fasten Gate Bracket to Gate 31
- Adjust Origin Clamp 32
- Gate closed 33
- Gate open 33
- For V400 (400mm operator) 34
- For V500 (500mm operator) 35
- Outward Swing Gate Setup 36
- FIGURE 53 37
- FIGURE 54 37
- FIGURE 55 38
- FIGURE 56 38
- FIGURE 57 39
- FIGURE 58 39
- 12. Allowable Wind Load 40
- Secure Control Box to Wall 41
- Connect all Wiring 41
- Setting the Limits 42
- FIGURE 65 43
- Master Motor (MTR M) 48
- Slave Motor (MTR S) 49
- Fuse protection 50
- 21. Solar Panel Wiring 51
- FIGURE 74. VIEW OF CONTROLLER 52
- 23. Menu Navigation Map 53
- 24. Controller Features 56
- Menu 4 - Modes of Operation 57
- Menu 5 - Run Profile 57
- FIGURE 78 58
- FIGURE 77 58
- FIGURE 76 58
- FIGURE 75 58
- Menu 6 59
- IR beams 59
- FIGURE 80 60
- FIGURE 81 61
- FIGURE 82 61
- Menu 7 - Pedestrian Opening 62
- Menu 8 - Gate Lock 63
- Menu 10 - General Features 64
- Menu 11 - Remote Controls 65
- 25. Factory Defaults Schedule 67
- CE Standard Profile 69
- UL325 Standard Profile 71
- 27. Diagnostics 76
- LCD Display 77
- Buzzer Feedback 78
- 28. Installation Handover 79
- Head Office: +27 11 699 2400 82
- +27 11 699 2481 82
Related products and manuals for Garden tools Centurion VECTOR2
Garden tools Centurion D3 User's Guide
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 0.356 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals